|
S80 '98-'06 / S60 '00-'09 / V70 & XC70 '00-'07 General Forum for the P2-platform S60 / V70 / XC70 / S80 models |
Information |
|
Removing the front bumper coverViews : 170389 Replies : 60Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Mar 17th, 2010, 18:46 | #21 |
New Member
Last Online: Aug 21st, 2017 18:59
Join Date: Nov 2004
Location: Edinburgh
|
Headlamp Wiper
Hi there,
Given this a try but absolutely stumpped by the headlamp wipers. As directed, got two bolts out and six 'plugs' near engine bay but the plastic bumper hole is obviously not big enough for the wiper component to fit through. Is there a way to remove the actual wiper arm to allow removal of the bumper? Thanks, |
Mar 18th, 2010, 19:13 | #22 |
New Member
Last Online: Aug 21st, 2017 18:59
Join Date: Nov 2004
Location: Edinburgh
|
Fog Lamp Done - but with wipers
Hi,
Just replaced RH front fog by removing bumper- very useful guide but posting the following as i noticed a few differences. '02 S60 (winter pack) Both rubbing strips removed with fingers 2x 12mm bolts removed 6x push out plug things above grill On each side, I had an additional plastic/nylon nut and bolt/screw on the bottom corner of the horizontal part of the bumper (just before the wheel arch). Think this was a 10mm nut and the bolt had a slot for flat head screwdriver. To remove headlamp wiper arms, first pull off the washer tube. at the bottom of the arm, where the hinge mechanism is, there is a cover which flips up to expose a 8mm nut. Undo this completely then pull of the arms - mines required a bit of persuading :-) You should now be able to remove the bumper. Once exposed, the fog is held in place by three torx 25 screws. remove. There is a locking mechanism for the cable - push the metal catch in and remove the cable from the back of the lamp. Fit new lamp. When putting bumper back on make sure washer tubes are put through hole in bumper first! Hope that helps someone! |
Mar 21st, 2010, 14:27 | #23 |
S60 Reg Keeper (Retired)
Last Online: Jun 10th, 2023 11:03
Join Date: Dec 2001
Location: Raxocoricofallipatorious
|
I attempted to remove the bumper cover a few weeks back when trying to change a headlamp bulb (see my writeup in the next Driver...!); got all the bolts, clips etc out (even managed to not crack the chrome inserts) but was ultimately thwarted in my attempts by the washer jets (post-facelift car). The covers for the jets are, naturally, wider than the holes they cover; I could see they should unclip somehow but didn't want to try and force anything in case I broke it!
Anyone know how to remove the top of the washer jet?
__________________
MY05 S60 2.0T SE...no more MY16 V60 T6 Polestar MY71 H.S.121-3B-101 http://www.savethetrident.co.uk/ Campaign to save G-ARPO, the last surviving Trident 1C |
Jun 2nd, 2010, 14:49 | #24 |
Junior Member
Last Online: Mar 9th, 2023 20:33
Join Date: Jun 2010
Location: East Kilbride
|
I too am trying to remove the front bumper, but mine sounds different to your description and all the removal articles posted widely.
Firstly, no-one seems to mention the arch liner. Have I picked it up right that it is held in place with pop rivets which must therefore be drilled out and replaced with new? (I'd rather know before I start wrecking things!) Secondly, I don't see any torx screw inside the wheel arch (unless it is covered over by the liner?). There is only a torx-keyed screw at the very corner of the plastic bumper, and it doesn't push in - it screws right out yet the bumper is still rigid. There is something securing it at the metal/plastic junction underneath the running light. I hope everybody sees this post as it is a reply to a now very old thread. (I may post it elsewhere). |
Jun 2nd, 2010, 19:41 | #25 |
S60 Reg Keeper (Retired)
Last Online: Jun 10th, 2023 11:03
Join Date: Dec 2001
Location: Raxocoricofallipatorious
|
You don't need to remove the wheel arch liners; the torx bolt is at the top corner of the bumper, just in the wheelarch, and the only "pop rivets" that have to be removed are the plastic ones top and bottom, where you push in the central pin and lft out.
__________________
MY05 S60 2.0T SE...no more MY16 V60 T6 Polestar MY71 H.S.121-3B-101 http://www.savethetrident.co.uk/ Campaign to save G-ARPO, the last surviving Trident 1C |
Jun 30th, 2010, 00:59 | #26 |
New Member
Last Online: Jun 30th, 2010 01:03
Join Date: Jun 2010
Location: Swedesboro, NJ
|
How do you remove the headlight wiper assembly
Your post on removing the front bumper was very helpful. However, I have headlight wipers and they are holding up the removal of the bumper. Do you know how to remove the wipers?
|
Jun 30th, 2010, 10:11 | #27 |
S60 Reg Keeper (Retired)
Last Online: Jun 10th, 2023 11:03
Join Date: Dec 2001
Location: Raxocoricofallipatorious
|
See post 22 above...
__________________
MY05 S60 2.0T SE...no more MY16 V60 T6 Polestar MY71 H.S.121-3B-101 http://www.savethetrident.co.uk/ Campaign to save G-ARPO, the last surviving Trident 1C |
Jul 1st, 2010, 23:15 | #28 |
New Member
Last Online: Sep 28th, 2013 16:42
Join Date: Apr 2009
Location: Tonbridge
|
Same for S80 2002?
I will be removing bumper to replace the aircon condenser, so just wanted to check that the S60 instructions would be the same for a S80.
Also, anyone know of part number for the 5 or 6 plastic push in clips if they need to be renewed? Thanks. |
Jul 9th, 2010, 17:05 | #29 | |
New Member
Last Online: Oct 11th, 2010 11:24
Join Date: Jul 2010
Location: london
|
Quote:
|
|
Aug 1st, 2010, 15:53 | #30 |
GoldMember
Last Online: Jul 19th, 2024 21:13
Join Date: Jul 2010
Location: Kent, UK
|
Very useful
Hi Capt,
Was very useful info as i had to remove mine recently also,, i found out a useful things about the washer jet things & how to remove them if you have a later 04 onward S60, i will post soon with some pictures, promises promises! |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|