|
x40 S1 Articles Article posts pertaining to x40 S1 Articles series Volvos |
Information |
|
How to replace the Front Seat BeltViews : 39354 Replies : 43Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Aug 18th, 2011, 20:28 | #1 |
Premier Member
Last Online: Nov 15th, 2022 21:34
Join Date: Apr 2010
Location: London / Essex
|
How to replace the Front Seat Belt
This is a guide of how to replace the drivers seat belt. This is only a guide and I would advice caution when attempting to follow my instructions, as there is a pyrotechnic device at the bottom part of the seatbelt mechanism which is meant to be activated in case of an accident.
Even though we will not be disconnecting any of the SRS cables, I would strongly advice disconnecting the battery and waiting for at least 20 minutes before you start. Also make sure that you have the Stereo security code handy before you disconnect the battery. First thing to do is to undo the two screws on the drivers trim and lift it up carefully. Also remove the rear passengers door trim You need to remove this plastic trim. Easy to take out. There is one clip on the top right hand side of it which releases very easily. See also next photo. Do not remove the screw hoplding the seatbelt yet. We will do so later on. Remove the lower plastic trim first. release the lower part first and then wiggle it out. Undo a bit of the inner door seals on both the drivers and rear passengers door frames (see photo). Be a bit careful with the top grey plastic trim. If you just pull it, you may break the plastic clip holding it. The way to remove it is to push gently the lower part towards the front of the car (see arrow) and it will come of the clip. Then move it slightly downwards and take it out. check the next two photos and you will see what I mean Remove the metal clip from the car frame and put it back in its place on the upper grey trim. You will need to push the two ends of the clip so it is released from the frame And now the fun bit. You can either remove the whole unit and take it indoors and change the seatbelt, or follow my instructions below. I found this to be easier and faster. Pull out the seatbelt all the way out. When doing so, try to have the part highlighted in the green circle (oval) facing the way I have it on the photo. You will have to pul out the seatbelt from there. The spring mechanism needs to be secured to this position. To do so, I used some electrical tape. I used 3 bits and the mechanism was not moving any more. Use you common sense when doing so and be careful the tape comes undone. If this happens, you will have to rewind the whole rotating mechanism and you will not know how far to go. So whatever you do, make sure you secure it properly. See also next photo of how I secured it. Once secured, pull out the seatbelt and slide off the pin which is securing it on the rotating spring mechanism. See also next photo Before you pull out the seatbelt, feed the new seatbelt though the upper plastic trim and have it ready to be fitted to the rotating mechanism. Pull out the old seatbelt and immediately feed the new one through the gap and secure it with the pin. In order to feed the new seatbelt in, you will have to rotate the spring mechanism about 90 degrees. If you have taped the mechanism the same way I did, it should be able to move in one direction only. Undo the bolt (size 14 socket), remove the old seatbelt and put the new one in. Job done. Well you need to put everything back together in the reverse order. Good luck and if you have any questions, suggestions or better ways to do things, please feel free to comment
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
Last edited by gatos; Aug 18th, 2011 at 20:31. |
The Following 24 Users Say Thank You to gatos For This Useful Post: |
Aug 18th, 2011, 21:19 | #2 |
Premier Member
Last Online: Jul 9th, 2020 20:08
Join Date: Dec 2007
Location: Halifax West yorkshire
|
That is a cracking "how to" guide and it is going to make changing my seatbelt so much easier, thank you.
|
Aug 18th, 2011, 21:35 | #3 |
Senior Member
Last Online: Sep 23rd, 2014 23:59
Join Date: Apr 2010
Location: Yorkshire
|
Great set of photos there, accompanied by a good script!
I've a couple of questions if I may... have you used a new seat belt for replacement and if so how much did it cost. I was all waiting from the very beginning of reading that, to expect a piece of red plastic which is hidden behind the plastic cover used to wedge the bottom seat attachment, for something which acts as a safety device. I wonder if it's only for use on different phase models... think I ought to be searching Done a bit of searching and it would appear to be the older phases had a mechanical SIPS system.
__________________
Year 2004 V40 1·6s Last edited by The Improver; Aug 18th, 2011 at 21:46. |
Aug 18th, 2011, 23:52 | #4 | |
Premier Member
Last Online: Nov 15th, 2022 21:34
Join Date: Apr 2010
Location: London / Essex
|
Quote:
I had two spare seatbelts from the car I am breaking. One went to stevo48 and one in my car as my drivers belt was not in the best condition. I was hoping that the rear seatbelts would work too, but they are a bit longer and they have a slightly different lower adaptor on the bottom. I may have one more seatbelt from last year, but I am not sure where it is. If I find it I will pm you. I will post some photos and info tomorrow about the length of the belt and and the shape of the lower metal bit
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
Last edited by gatos; Aug 19th, 2011 at 00:00. |
|
Aug 19th, 2011, 10:24 | #5 |
Senior Member
Last Online: Sep 23rd, 2014 23:59
Join Date: Apr 2010
Location: Yorkshire
|
Gatos many thanks for your answers my V40 is a Phase 2, so there aint no RED bit... we're electric. The thread I'd seen the RED bit in was DWM's Retro fitting heated seats and he'd done it on a 97' Phase 1.
I was just trying to prepare myself for future cost of new front belts... I think new ones might take a deep breath before ordering! It's a shame Volvo didn't design the door pillar covers with a bit more thought... I assume its the sawing action of the belt thro' the plastic that causes the problem, isn't it.
__________________
Year 2004 V40 1·6s |
The Following User Says Thank You to The Improver For This Useful Post: |
Aug 19th, 2011, 10:46 | #6 |
Premier Member
Last Online: Nov 15th, 2022 21:34
Join Date: Apr 2010
Location: London / Essex
|
Yes that seems to be the most probable cause. I remember seeing a guide somewhere of how to fit a U shaped metallic sleeve, that would stop both belt and cover getting damaged. Will search around to try to find it
Edited: Found it. 4 forty is the one who did it. Will pm him for photo and how too.... Thread is here: http://www.volvoforums.org.uk/showthread.php?t=9186 Also thanks to Andy_d for pointing out to me the torque settings for the seatbelt bolts. They should be both tightened to 48Nm / 35 foot pounds
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
Last edited by gatos; Aug 19th, 2011 at 11:19. |
Aug 21st, 2011, 18:27 | #8 |
Premier Member
Last Online: Nov 15th, 2022 21:34
Join Date: Apr 2010
Location: London / Essex
|
Glad I could help...
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
|
Oct 11th, 2011, 12:50 | #9 |
I've Been Banned
Last Online: May 13th, 2015 12:51
Join Date: Oct 2011
Location: Greenwich
|
Cheers mate, it worked a treat and I didn't break a thing.
|
Nov 7th, 2011, 17:34 | #10 |
New Member
Last Online: Nov 15th, 2017 06:57
Join Date: May 2010
Location: Dublin
|
I'm over in Ireland and have the same issue with the belt fraying from the trim aperture.
I see a fair number of used passenger side belts on the internet but second hand Drivers side ones are much rarer. Can I use just the belt from one of these near side units as a replacement on the drivers side??? |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|