|
S80 '06-'16 / V70 & XC70 '07-'16 General Forum for the P3-platform S80 and 70-series models |
Information |
|
Rear trailing arm bush.Views : 6828 Replies : 48Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Dec 12th, 2020, 09:52 | #1 |
Premier Member
Last Online: Yesterday 21:13
Join Date: Aug 2008
Location: Newcastle
|
Rear trailing arm bush.
I have been trying to gather information about this bush, which historically has proven to be a weak point. I would like to be prepared for replacement, as time statically would suggest failure is just around the corner, despite showing no signs ( to me) of failure - no squeaks or other noise. Despite several thread on here, I'm left with more questions than answers, as the more I find out the less I find I know...
1) There has been a design change of the bush, mine has it but did this solve the problem of corrosion/lamination? I have been unable to find failures in cars registered after circa 2013. So is that a "Yes"? 2) The removal tools ( draper+ sealey) refer to fitting only upto 2012/3 vehicles , not mine. Did the design change make these tools unsuitable for 2013+ vehicles, or is this merely a facelift demarkation by the tool manufacturers ?? 3) Cheaper removal tools are available on Ebay - for 50% of the Draper/Sealey tool. Anyone used these tools and how did they perform?. Seen several utube videos of these tools in operation and it all looks very simple, but is it.? The bush itself - some suggest the Mondeo bush ( cheaper) can be used as its the same as Volvo, anyone actually used the Ford bush? Anyone used polybushing? Lots of questions I know, but this bush from what I read on this site, and else where is the P3 Achilles heal. It would be nice to gather all the information about this bushing at one point for future reference??? 2015 V70 D5 Manual. Cheers Bob Last edited by 100K+; Dec 12th, 2020 at 09:53. Reason: additions |
Dec 25th, 2020, 23:01 | #2 |
Spannering since birth
Last Online: Yesterday 17:06
Join Date: Jul 2006
Location: North Oxon
|
Following this thread.
Yes I believe the bush was redesigned at some point. I changed the bushes on my 2011 V70 a few months back using the Sealey tool and Lemforder bushes. The bushes were original with 118,000 miles & completely in bits. Not easy on the driveway, took longer than I expected, the tool is heavy and tricky to push bushes in square. The trick is to pull the arm down as low as possible to get good access to the arm. Be interested in any feedback on the poly bushes, I did consider but couldn't find much feedback on them.
__________________
V70 D5 eu4 manual M66 2006 > XC90 brake conversion, stage 2 VDASH remap. BMW R1200GS BMW R1100GS (GS Addict) |
The Following User Says Thank You to john493 For This Useful Post: |
Dec 26th, 2020, 22:07 | #3 |
Premier Member
Last Online: Yesterday 21:13
Join Date: Aug 2008
Location: Newcastle
|
Thanks for your reply. I thought this would have been a fairly common repair - like the drop links or wishbones on P2's. but with only one response in over 100+viewings these bush failures aren't as common as I thought. Interested to hear tool is heavy and fitting of bushes is not as quick as you thought. I have seen a couple of utube videos and it looks very simple and quick. The tool plus bushes cost is not too far away from what Volvo or an indi might charge. The real savings would come if you had to do the job a 2nd time, which if you used poly bushes could be never.
Cheers Bob. |
Dec 30th, 2020, 00:35 | #4 | |
Premier Member
Last Online: Today 00:12
Join Date: Apr 2019
Location: Manchester
|
Quote:
On that note, my Dad has a V70 estate (57 plate) with 157k on it & the rear trailing arm bushes are starting to perish slightly on his car too... It was MOT'd at the same indi that did the work on mine. There's no excessive movement or noise yet, but I was told when collecting the car on my Dad's behalf that they won't last forever & will need replacing at some point. When the time comes, I'll let the garage replace them. Just one last thing to note, you'll need to get an alignment after getting the rear trailing arm bushes replaced.
__________________
2007 S80 2.4 D5 (P3) - 110,000 miles 2008 V70 2.4 D5 (P3) - 163,000 miles |
|
Dec 31st, 2020, 11:08 | #5 | |
Premier Member
Last Online: Yesterday 21:13
Join Date: Aug 2008
Location: Newcastle
|
Quote:
Cheers Bob |
|
Dec 31st, 2020, 12:04 | #6 |
Spannering since birth
Last Online: Yesterday 17:06
Join Date: Jul 2006
Location: North Oxon
|
There's adjustment at the point the trailing arm bushes bolt onto the floor pan.
No adjustment should be needed just changing a rear spring, although you might get it checked as a precaution.
__________________
V70 D5 eu4 manual M66 2006 > XC90 brake conversion, stage 2 VDASH remap. BMW R1200GS BMW R1100GS (GS Addict) |
The Following User Says Thank You to john493 For This Useful Post: |
Jan 2nd, 2021, 01:38 | #7 | |
Premier Member
Last Online: Today 00:12
Join Date: Apr 2019
Location: Manchester
|
Quote:
As you've just replaced a spring so far & not the trailing arms, then no alignment will be needed.
__________________
2007 S80 2.4 D5 (P3) - 110,000 miles 2008 V70 2.4 D5 (P3) - 163,000 miles |
|
Jan 20th, 2021, 16:27 | #8 |
Junior Member
Last Online: Nov 21st, 2023 09:18
Join Date: May 2019
Location: Fleet
|
Out of interest, this was mentioned by my garage the last time they serviced the car as a future item to deal with. For a garage (I am not able to do this) to replace the rear trailing arm bushes, what have people been quoted/paid?
|
Jan 21st, 2021, 12:28 | #9 | |
Premier Member
Last Online: Today 00:12
Join Date: Apr 2019
Location: Manchester
|
Quote:
At a main dealer, it could cost more.
__________________
2007 S80 2.4 D5 (P3) - 110,000 miles 2008 V70 2.4 D5 (P3) - 163,000 miles |
|
The Following User Says Thank You to Kev0607 For This Useful Post: |
Jan 21st, 2021, 15:17 | #10 | |
Premier Member
Last Online: Yesterday 21:13
Join Date: Aug 2008
Location: Newcastle
|
Quote:
Cheers Bob. |
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|